Karmag
08-09-2023, 14:53
Z tymi bledami silnik pracuje normalnie auto nie jedzie bo jest brak reakcji na zmiane biegow(dct450) dopiero jak ostygnie to wszystko wraca do normy...
===PCM DTC U0415:86-A8===
Code: U0415 - Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A'
Additional Fault Symptom (:86):
- Signal Invalid
Status (-A8 ):
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Powertrain Control Module
Freeze Frame #1:
-EVENT_TIME: 358845377 s (Fri Sep 08 11:49:23 2023) - Event time
-TOTAL_DISTANCE: 188739 km - Total Distance
-MODULE_VOLTAGE: 14.3 V - Control Module Voltage
-ESTSERUN: No - Engine status - engine running
-ESTSECRK: Yes - Engine status - engine in crank
-INCAR_TEMPERATURE: 15 °C - In car temperature
-OUTDOOR_TEMPERATURE: 15 °C - Outside temperature
-PWR_MODE_KEY: Crank - Power Mode Key State
-PWR_MODE_QF: Power Mode Undefined - Power Mode Quality Factor
-LOAD: 11.76 % - Calculated Load Value
-ECT: 82 °C - Engine coolant temperature
-MAP: 99.0 kPa - Manifold absolute pressure sensor
-RPM: 797 1/min - Engine Revolutions Per Minute
-VSS: 0.0 km/h - Vehicle Speed
-IAT: 24 °C - Intake Air Temperature
-MAF: 0.60 g/s - Mass Air Flow
-FRP: 32900.0 kPa - Fuel Rail Pressure
-BARO: 98.0 kPa - Barometric pressure
-APP_D: 0.00 % - Accelerator Pedal Position D
===END PCM DTC U0415:86-A8===
===OBDII DTC U0415-C===
Code: U0415 - Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A'
Status (-43):
- Confirmed - malfunction is confirmed
Module: On Board Diagnostic II
===END OBDII DTC U0415-C===
===TCM DTC None===
Successful DTC reading, no error codes found
Module: Transmission Control Module
===END TCM DTC None===
===AWD DTC B2477-40===
Code: B2477 - Module Configuration Failure
Status (-40):
- DTC Maturing - Intermittent at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: All Wheel Drive Module
Diagnostic Trouble Code details
Module Configuration Failure
===END AWD DTC B2477-40===
===ABS DTC C1233-A0===
Code: C1233 - Left Front Wheel Speed Sensor Input Signal Missing
Status (-A0):
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Antilock braking system
Diagnostic Trouble Code details
The left front wheel speed sensor input signal is missing or the signal is not plausible.
The code is set normally when the speed from one sensor differs from the speed on the other three sensors. The vehicle speed must exceed 40 kph (25 mph) for this code to be set.
A fault has been reported. At some time a wheel speed signal has been out of range. The possible causes are as follows:
Damaged wheel speed sensor.
Sensor air gap too large.
The vehicle has been towed on two wheels.
A road wheel has been dynamically balanced on the vehicle while the IN2IGN iwas in position II or shortly after IN2IGN off.
The vehicle has been driven on a two wheel rolling road.
There is a short duration intermittent open circuit on the sensor wiring.
The vehicle has been accident damaged or abused (eg. rolled spun parking brake turns etc.)
The tires installed have varying outside diameters.
A wheel bearing is worn or loose.
Additional Information
The ABS lamp should be illuminated.
The ESP lamp should be illuminated.
There will be an ESP malfunction warning displayed on the driver information text panel.
===END ABS DTC C1233-A0===
===EPS DTC None===
Successful DTC reading, no error codes found
Module: Electronic-Controlled Power Steering
===END EPS DTC None===
===IC DTC U1900-20===
Code: U1900 - CAN communication bus fault
Status (-20):
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Cluster
Diagnostic Trouble Code details
CAN Communication Bus Fault - Receive Error
Note:
DTCs that start with 'U' are faults which occur during module-to-module communication.
Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle.
===END IC DTC U1900-20===
===PDM DTC None===
Successful DTC reading, no error codes found
Module: Passengers Door Control Unit
===END PDM DTC None===
===DFDM DTC None===
Successful DTC reading, no error codes found
Module: Driver Door Control Unit
===END DFDM DTC None===
===RCM DTC None===
Successful DTC reading, no error codes found
Module: Restraint Control Module
===END RCM DTC None===
===EATC DTC None===
Successful DTC reading, no error codes found
Module: Electronic Automatic Temperature Control
===END EATC DTC None===
===RKE DTC U0101-20===
Code: U0101 - Lost Communication With The TCM
Status (-20):
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Remote Keyless Entry
===END RKE DTC U0101-20===
===GEM DTC None===
Successful DTC reading, no error codes found
Module: Generic Electronic Module
===END GEM DTC None===
===PCM DTC U0415:86-A8===
Code: U0415 - Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A'
Additional Fault Symptom (:86):
- Signal Invalid
Status (-A8 ):
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Powertrain Control Module
Freeze Frame #1:
-EVENT_TIME: 358845377 s (Fri Sep 08 11:49:23 2023) - Event time
-TOTAL_DISTANCE: 188739 km - Total Distance
-MODULE_VOLTAGE: 14.3 V - Control Module Voltage
-ESTSERUN: No - Engine status - engine running
-ESTSECRK: Yes - Engine status - engine in crank
-INCAR_TEMPERATURE: 15 °C - In car temperature
-OUTDOOR_TEMPERATURE: 15 °C - Outside temperature
-PWR_MODE_KEY: Crank - Power Mode Key State
-PWR_MODE_QF: Power Mode Undefined - Power Mode Quality Factor
-LOAD: 11.76 % - Calculated Load Value
-ECT: 82 °C - Engine coolant temperature
-MAP: 99.0 kPa - Manifold absolute pressure sensor
-RPM: 797 1/min - Engine Revolutions Per Minute
-VSS: 0.0 km/h - Vehicle Speed
-IAT: 24 °C - Intake Air Temperature
-MAF: 0.60 g/s - Mass Air Flow
-FRP: 32900.0 kPa - Fuel Rail Pressure
-BARO: 98.0 kPa - Barometric pressure
-APP_D: 0.00 % - Accelerator Pedal Position D
===END PCM DTC U0415:86-A8===
===OBDII DTC U0415-C===
Code: U0415 - Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A'
Status (-43):
- Confirmed - malfunction is confirmed
Module: On Board Diagnostic II
===END OBDII DTC U0415-C===
===TCM DTC None===
Successful DTC reading, no error codes found
Module: Transmission Control Module
===END TCM DTC None===
===AWD DTC B2477-40===
Code: B2477 - Module Configuration Failure
Status (-40):
- DTC Maturing - Intermittent at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: All Wheel Drive Module
Diagnostic Trouble Code details
Module Configuration Failure
===END AWD DTC B2477-40===
===ABS DTC C1233-A0===
Code: C1233 - Left Front Wheel Speed Sensor Input Signal Missing
Status (-A0):
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Antilock braking system
Diagnostic Trouble Code details
The left front wheel speed sensor input signal is missing or the signal is not plausible.
The code is set normally when the speed from one sensor differs from the speed on the other three sensors. The vehicle speed must exceed 40 kph (25 mph) for this code to be set.
A fault has been reported. At some time a wheel speed signal has been out of range. The possible causes are as follows:
Damaged wheel speed sensor.
Sensor air gap too large.
The vehicle has been towed on two wheels.
A road wheel has been dynamically balanced on the vehicle while the IN2IGN iwas in position II or shortly after IN2IGN off.
The vehicle has been driven on a two wheel rolling road.
There is a short duration intermittent open circuit on the sensor wiring.
The vehicle has been accident damaged or abused (eg. rolled spun parking brake turns etc.)
The tires installed have varying outside diameters.
A wheel bearing is worn or loose.
Additional Information
The ABS lamp should be illuminated.
The ESP lamp should be illuminated.
There will be an ESP malfunction warning displayed on the driver information text panel.
===END ABS DTC C1233-A0===
===EPS DTC None===
Successful DTC reading, no error codes found
Module: Electronic-Controlled Power Steering
===END EPS DTC None===
===IC DTC U1900-20===
Code: U1900 - CAN communication bus fault
Status (-20):
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Cluster
Diagnostic Trouble Code details
CAN Communication Bus Fault - Receive Error
Note:
DTCs that start with 'U' are faults which occur during module-to-module communication.
Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle.
===END IC DTC U1900-20===
===PDM DTC None===
Successful DTC reading, no error codes found
Module: Passengers Door Control Unit
===END PDM DTC None===
===DFDM DTC None===
Successful DTC reading, no error codes found
Module: Driver Door Control Unit
===END DFDM DTC None===
===RCM DTC None===
Successful DTC reading, no error codes found
Module: Restraint Control Module
===END RCM DTC None===
===EATC DTC None===
Successful DTC reading, no error codes found
Module: Electronic Automatic Temperature Control
===END EATC DTC None===
===RKE DTC U0101-20===
Code: U0101 - Lost Communication With The TCM
Status (-20):
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Remote Keyless Entry
===END RKE DTC U0101-20===
===GEM DTC None===
Successful DTC reading, no error codes found
Module: Generic Electronic Module
===END GEM DTC None===